Advanced project 110b ESP8266 ESP-12E module, thermistor and 5VDC relay module – Protected Web server


Advanced: Project 110b

Project name:  ESP8266 ESP-12E module, thermistor and 5VDC relay module – Protected Web server

Tags: Arduino IDE, ESP8266 ESP-12E module, Nodemcu v3, Lolin, thermistor, 5VDC relay module

Attachments: sketch

In this project, you needed these parts (Dear visitors. You can support our project buy clicking on the links of parts and buying them or donate us to keep this website alive. Thank you):

1. ESP8266 ESP-12E module and Micro USB cable 1pc

A6 GSM GPRS module

2.Arduino IDE (you can download it here)

3. Breadboard 1 pc

breadboard

4. Thermistor 1 pc

thermistor

5. Resistor 10 KOhm 1 pc

resistor

6. Jumper wires F-M, M-M

wires

7. 5VDC relay module with 2 ch 1 pc

5vdc relay module

General

We will learn how to make a simple protected web server to control some 5VDC relay modules and show the temperature from thermistor.

Understanding the thermistor

A thermistor is a type of resistor whose resistance is dependent on temperature, more so than in standard resistors. The word is a combination of thermal and resistor. Thermistors are widely used as inrush current limiters, temperature sensors (negative temperature coefficient or NTC type typically), self-resetting overcurrent protectors, and self-regulating heating elements (positive temperature coefficient or PTC type typically).

Thermistors are of two opposite fundamental types:

  • With NTC thermistors, resistance decreases as temperature rises. An NTC is commonly used as a temperature sensor, or in series with a circuit as an inrush current limiter.
  • With PTC thermistors, resistance increases as temperature rises. PTC thermistors are commonly installed in series with a circuit, and used to protect against overcurrent conditions, as resettable fuses.

Undestanding the relay module

You can read more about it here.

Understanding the ESP8266 ESP-12E WI FI module (LoLin NODEMCU V3)

You can read more about it here.

Signals and connections of the ESP8266 ESP-12E WI FI module (LoLin NODEMCU V3)

A6 GSM GPRS module

TX – transmit pin. GPIO pin

RX  – receive pin.  GPIO pin

3V3 (or 3V or 3.3V)- power supply pin (3-3.6V). 

GND ( or G) – ground pin.

RST – reset pin. Keep it on high (3.3V) for normal operation. Put it on 0V to reset the chip.

EN – Chip enable. Keep it on high (3.3V) for normal operation.

Vin – External power supply 5VDC.

D0-D8 – GPIO (General Purpose Input Output) pins 

D5-D8 – SPI interface

D1-D2– I²C/TWI Interface

SC (or CMD) – (Chip Select) – the pin that the master can use to enable and disable specific devices. GPIO pin

SO (or SDO) – Master In Slave Out (MISO) – SPI communication. The Slave line for sending data to the master. GPIO pin

SK (or CLK) – SCK (Serial Clock) – SPI communication.The clock pulses which synchronize data transmission generated by the master. GPIO pin

S1 (or SD1) – Master Out/Slave In (MOSI). SPI communication. The Master line for sending data to the peripherals. GPIO pin

S2 (or SD2) – GPIO pin

S3 (or SD3) – GPIO pin

VU (or VUSB) – external power 5VDC.

A0 – ADC output.

RSV – reserved

Wiring

Nodemcu 1.0 5VDC relay module

GND GND

VU (5V) VCC

D1 (GPIO5) IN1

D2 (GPIO4) IN2

Step by Step instruction

1. Adding ESP8266 platform to Arduino IDE

The Arduino environment has to be set up to make it compatible with the ESP8266 ESP-12E module. We are using PC with Windows 7 64 bit OS.

Download and install the Arduino IDE. You can download it here 

Open Arduino IDE. 

Open the Preferences window from the Arduino IDE. Go to File -> Preferences.

A6 GSM GPRS module

Enter http://arduino.esp8266.com/stable/package_esp8266com_index.json into Additional Board Manager URLs field and click the “OK” button. If you already have a URL in there, and want to keep it, you can separate multiple URLs by placing a comma between them. (Arduino 1.6.5 added an expanded text box, separate links in here by line.)

A6 GSM GPRS module

Open Boards manager. Go to Tools -> Board -> Boards Manager…

A6 GSM GPRS module

There should be a couple new entries in addition to the standard Arduino boards. Look for esp8266. or scroll down to the ESP8266 entry (usually at the bottom). Select the ESP8266 entry. When you click it an install option will appear. Select the latest version and click install

A6 GSM GPRS module

The board definitions and tools for the ESP8266 include a whole new set of gcc, g++, and other reasonably large, compiled binaries, so it may take a few minutes to download and install (the archived file is ~110MB). Once the installation has completed, an Arduino-blue “INSTALLED” will appear next to the entry.

A6 GSM GPRS module
A6 GSM GPRS module

2. Uploading sketch to ESP8266 ESP-12E development board

If you’re using an ESP-12E NodeMCU Kit, uploading the sketch is very simple, since it has built-in programmer. 

Before use ESP8266 ESP-12E WI FI module (LoLin NODEMCU V3), you need to download the manufacture’s driver (CH340)  for this chip and install it in your PC. Here is the link. See the description of driver installation package below: CH340 / CH341 USB to serial WINDOWS driver installation package that supports 32/64 bit Windows 10 / 8.1 / 8/7 / VISTA / XP, SERVER 2016/2012/2008/2003, 2000 / ME / 98, through Microsoft digital signature authentication, support USB to 3-wire and 9-wire serial port, with the product release To the end user. Applicable scope: CH340G, CH340C, CH340B, CH340E, CH340T, CH340R, CH341A, CH341T, CH341H chips.

If you have CP2102 chip then  you need to download the manufacture’s driver for this chip and install it in your PC. Driver for MacWindowsLinux or more.. 

  1. Do wiring.
  2. Open Arduino IDE.
  3. Plug your ESP8266 ESP-12E module into your PC USB port.
  4. Choose your NodeMCU board. Go to Tools -> Board -> NodeMCU 1.0 (ESP-12E Module)
  5. Select the correct com port.
  6. Modify the sketch with your local network SSID and password and required IP address, gateway, subnet, primary DNS, secondary DNS, web server port; you will also need to change username and password (by default they are admin/admin).
  7. Verify and upload it to your ESP8266 ESP-12E module.
  8. After uploading the code open the Arduino IDE Serial monitor at 115200 bps. Press onboard RST button. You will see the IP address (in our case IP address is 192.168.1.211)
  9. Open any web browser and type in http://your-ip-address (in our case http://192.168.1.211).
  10. Type your username and password and click on Login button.
  11. You can see the temperature readings and can control 5VDC relay module with 2 channels. You can also see the state of each GPIO pin.
nodemcu protected web server
nodemcu web server protected
nodemcu web server protected
nodemcu thermistor

Summary

We have learnt how to make a simple protected web server to control some 5VDC relay modules and show the temperature from thermistor.

Thank you for reading and supporting us.

Libraries:

  • No libraries required for this project

Project resources:

  • See attachments on the beginning of this project description

AcoptexCom

Has one comment to “Advanced project 110b ESP8266 ESP-12E module, thermistor and 5VDC relay module – Protected Web server”

You can leave a reply or Trackback this post.
  1. ปั๊มไลค์ - 2020 June 2 Reply

    Like!! Great article post.Really thank you! Really Cool.

Leave a Reply

Your email address will not be published.